Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - woody

Pages: [1] 2 3 ... 19
Technical / A common fault in nearly all Pulse Induction detectors
« on: March 07, 2022, 09:17:06 am »
There is a subtle design anomaly in just about every pulse induction detector that can limit the depth capabilities of the detector. Nothing in this world is perfect but with some added engineering the depth problem can be greatly reduced.

Noisy coils and how to repair. / Why is my coil noisy?
« on: January 22, 2022, 05:14:01 pm »
Most likely it is that the carbon, and or graphite paint the shields the coil windings have worn through. This is very common and best explained with pictures and video.

Technical / GPZ7000 handshake coil work around.
« on: January 11, 2022, 11:52:11 am »
There are a couple of ways to use different coils if you really want to do it, cut the chip board from the coil plug and solder it to the inside of the detector, thus it will function on all test or after market coils. In the mean time I have been working on a way to have the detector ignore the handshake protocols, there has been some success and I will update as I progress.

General Discussion / GPZ 7000 and coils
« on: December 25, 2021, 11:24:15 am »
Here is a warning about trying after market coils on the GPZ 7000. Don’t do it! Any fault in the coil can destroy the coded handshake ic chip inside the detector, Minelab have a way of knowing (imho) that an after market coil was fitted by the nature of the damage, this has been told to me from prospectors that sent their blown up detectors to minelab to be repaired, I was told minelab refused to repair the detectors, so…In my opinion it is not wise to play around with this part of the detector, it can be a very expensive exercise.

General Discussion / EMI that noise that hides gold targets.
« on: December 22, 2021, 11:20:11 am »
There is nothing worse than trying to use an unstable metal detector that is making noise due to EMI, I have discovered that a rectification issue is embedded in nearly all pulse induction detectors that use semiconductors in the back emf blocking path, but there is a problem. As all these discoveries are hard won battles I am not going into technical discussion in order to hand over valuable discoveries and information to other parties for free. They say that others that copy your work is a form of flattery but it’s not, I have seen and heard that others tell customers that I copied their work and one in particular was telling people that he taught me everything that I know. This guy is a wanker, he was calling me up trying to milk me for information on detectors, he would say that it was only for his personal detector….lol anyway this is why I do not tell anyone my telephone it invites another form of EMI. That being said, we currently have an ex Minelab detector tester using our newest mods and his words are, “ this is the best detector that I have ever used” but he did say that EMI was still a big issue, so over the last four months I set out to try many different methods to remove EMI and retain greater sensitivity and depth while improving the ground balance accuracy. Well, I succeeded on all fronts, these improvements are for the GPX 4500 and 5000 but will also work on other pulse induction detectors. It is about time that I go out over the old detected gold fields and find gold that other detectors will never be able to find.
This is going to be like 1980 all over again. I’m excited.

New Detector design / Re: your dedector
« on: December 22, 2021, 10:56:08 am »
It’s coming, a very slow process as parts are difficult to acquire.

General Discussion / New mods as of December 2021
« on: December 14, 2021, 09:10:09 pm »
A lot of hard work has gone into a full blown components upgrade and new additional control boards, this is really not for hobby detectorists as it costs a lot to do, but is aimed at full time professionals that need to find gold every time they go out. Tests on hot ground at Red streak gully in Dunolly central Victoria show 17% more depth over standard detectors using 17" coil on 6 oz target. Expect to see me out going over as much old ground that I can.

General Discussion / Re: GPX 6000 VS Modded 5000
« on: December 14, 2021, 09:03:46 pm »
The new mods (GPX) will knock the socks off any of the newer detectors on depth and quietness.
Tested against standard GPX and GPZ.

General Discussion / Re: Detector mods Facebook group
« on: December 14, 2021, 09:01:13 pm »
Tested the latest upgrades today on a GPX, Hot ground on a 6 Oz target using 17" coil we improved the depth over a stock standard detector by 17% Improved ground balance and a lot lower noise.

Tested today at Red Streak Gully in Dunolly on red hot ground.
The newest upgrades in a GPX detector.

Using 17" coil and 6 Oz test nugget I can say that we gained 17% greater depth compared to a stock standard GPX detector. There is still more to come but it takes time.

I have around 3 or 4 designs on the go, sometimes they take 6 months to design and test, always a little bit different. There is also the new detector in the pipeline as well.

We are starting to run some new boards out that have a far greater performance on tiny gold and big deep gold using large coils. The new boards have a set of very fast low noise intermediate drivers added, inclusive of new components to give a different attack and decay phase shift that helps greatly with the ignoring of hot rocks.

This allows far more gain to be used while at the same time reducing the response to hot rocks and ground noises. The new settings allow the use of a large mono coil even in normal timings as to be adjustable to the point where it is far less sensitive to ground fluctuations and the dreaded hot rocks.

Now just because we put a turbo charger on the V8 it does not mean that you can wind everything full and go hoon around in the rain, you just end up doing wheel spins and getting nowhere fast.

The type of ground is the main thing that you have to deal with, red hot iron stone ground means to reduce the gain so that the input circuit of the detector is not overloaded by a huge ground signal, reducing the gain and the variable frequency control helps control the noise, 

In mild ground such as pipe clay and some river banks it is possible to run the gain nearly full on, this has not been possible before as the earth field creates too much of a weee wooo sound when moving the coil up and down a river bank.

As the biggest deepest gold is more likely to be found in normal timings the upgraded sub board allows the use of normal timings in most circumstances, even with a 24 inch coil. Tiny gold such as spurry reef or 0.005 gram bits are easily detected in Enhance mode with a small coil, running the variable frequency around 200 or more with the gain set as to allow perfect ground balance is outstanding. My own testing with a mono 10 x 5 coil on a 0.005 gram gold can actually cause an overload signal on the detector. This tiny gold was detected out to 8 cm.

The real testing should always be carried out on the ground that you intend to detect, bury a target such as a gold nugget or melted aluminium and try to get it so deep that you can just detect it, experiment with settings and coil sizes as to get the best depth without making the detector unstable and noisey.

After playing with the detector and if you get confused with the changes, its very simple to reset the detector by turning the detector off, holding the power switch down until it goes dee dee dah and turning the control to reset all, then turn the other control to do the reset. It is as basic as it sounds.

Well the Covid19 virus also known as the CHINESE virus or Wuhan Express, has really put a stop on doing any video or outdoor detecting as we are basically in a lock down situation. This has allowed me to carry out a lot of lab work trying out different arrangements to gain profiles and ground balancing. I have come up with some waveform phase mods that should allow a lot more depth on really big deep targets and reducing false ground noise targets. Only if i can get out to the test site and try it out in the real world. It works great on the work bench and reduces hot rock detection while allowing for a lot more gain.

New Detector design / Re: Any news?
« on: March 08, 2020, 04:39:31 pm »
Not yet, there is a good chance a complete new platform will be made available, but then it can all bog down and fall over. 

New Detector design / Re: Any news?
« on: March 07, 2020, 01:31:07 pm »
We have movement in this area, getting there.

Pages: [1] 2 3 ... 19